【Table of Contents】
I. Safety Warnings
II. Unpacking
III. User Registration
IV. 3D Printer Placement Environment
V. 3D Printer Management
VI. Main 3D Printer Components
VII. Intended Use
VIII. Connecting the 3D Printer
IX. Preparation for Printing
X. Product Output
XI. Cleaning
I. Safety Warnings
Please strictly follow the instructions below when using the printer.
The DWS XFAB 3D printer uses photosensitive resin, which can be hazardous if it comes into contact with skin and eyes. Therefore, exercise extreme caution when using the printer. In case of skin contact, rinse the affected area with plenty of water to avoid irritation. If it comes into contact with eyes, rinse with plenty of clean water for about 15 minutes, then seek emergency medical attention immediately.
Dried resin residue can damage the printer. Therefore, ensure that any resin residue on the printer is cleaned immediately.
Resin handling and disposal must comply with local legal requirements.
Tampering with the printer and its components is strictly prohibited. This is particularly important for the laser light to avoid compromising its safety.
If you notice defects or malfunctions, please contact the manufacturer immediately.
During the processing phase, do not:
1. Move the 3D printer.
2. Disconnect the power and computer power.
3. Disconnect the network connection.
4. Open the cover.
Do not alter the machine or software in any way. The manufacturer will disclaim all responsibility for any malfunctions after modifications to the machine or software.
II. Unpacking
①The box contains:
DWS XFAB 3D Printer
24V DC - 110-220V AC Power Supply
USB Cable
Cleaning kit includes:
– Comb Scraper
– Plastic Spatula
– Tweezers
– Spray Bottle
– Gloves
– Pliers
– Resin Filter
②Unpacking the 3D printer
Check the condition of the packaging and the top of the pyramid. If there are any dents or damages, please contact the manufacturer (support@dwssystems.com).
Unpack the printer as follows:
Warning: There may be a risk of cuts or abrasions when unpacking the printer.
1. Cut the plastic straps.
2. Open the top of the cardboard box.
3. Remove the box containing the printer accessories.
4. Carefully remove the cardboard box.
5. Remove the top polystyrene casing from the printer.
6. Turn the bottom polystyrene casing of the printer outward.
Warning: Two people are required to lift the printer.
Lift as follows:
Warning: Be careful not to bump the printer body when lifting it.
1. Hold the printer from the bottom edge.
Warning: To avoid back and waist injuries, bend your knees and squat down, keeping your torso straight.
2. Two people lift the printer together and place it in the designated area.
3. Remove and dispose of the packaging.
③Disposal of packaging materials
Always ensure compliance with local legal requirements when disposing of the following packaging materials:
- Wooden pallet
- Cardboard box
- Polystyrene casing
- Plastic straps
III. User Registration
1. Go to the page customers.dwssystems.com
2. Click "Sign in" to go to the registration page.
3. Enter the required information and follow the instructions to complete the registration.
4. Open the registration verification email and click the verification link.
5. Click "Verify" to complete the registration.
6. Click "Sign in".
7. Enter your username and password, then click "Login".
8. Click "Register 3D printer" to register your 3D printer.
9. Enter the serial number (located on the nameplate on the back of the printer) and printer model in the corresponding boxes, then click "Save".
10. If the printer is open, you can disconnect the printer from the registered user by clicking "Save".
IV. Printer Placement Environment
Place the printer on a stable, level, and clean surface, in a dust-free environment, away from direct sunlight, at a temperature of 20°-25°C.
V. Printer Management
To download the printer software, follow these steps:
1. Go to customers.dwssystems.com
2. If necessary, click "Sign in" and enter your username and password to log in.
3. Click "Software".
4. Download the "Fictor" software (PC minimum requirements: Windows 7 SP1 or later, OpenGL graphics card, dual-core processor, USB connection port).
5. Download the "Nauta" software (*) (32-bit or 64-bit, depending on the operating system).
6. Go to your downloads folder, click the installer you just downloaded to proceed with the installation.
7. To request the code required for installation, click "Licenses".
(*) See the "Nauta" software manual, go to the Help menu (View Help) within the program.
When initializing the "Fictor" program (Warning: The program may request administrator privileges during initialization. Answer YES when prompted by Windows), the main screen will open, displaying the following:
A. Open housing key.
B. Printer initialization key.
C. Printer status indicator.
D. Print status indicator.
E. Modeling platform display.
F. Display user settings control area (refer to E).
G. 3D print file selection key.
H. Print material selection key.
I. Print start key.
VI. Main 3D Printer Components
① Main Printer Components
J. Cover
K. Platform
K1. Knob
L. Platform Locking Handle
M. Resin Cartridge
M1. Resin Cartridge Top Cover
M2. Resin Cartridge Latch
M3. Resin Container (where resin is placed)
N. Removable Resin Tray
O. Laser Light (class 3B)
P. Fixing Rod
② Function Key List
Backlit ON/OFF key (Q), which displays the printer status, also shown on the software screen (C) as follows:
1. Black LED: Printer not connected
2. Purple LED: Printer connected
3. Green LED: Printer ready
4. Light Blue LED: Printer operating, laser light off
5. Blue LED: Printer operating, laser light on
6. Red LED: Error
7. Yellow LED: Printer paused
8. White LED: Cover open
VII. Intended Use
XFAB belongs to the SLA 3D printer (a 3D printer that uses laser light to cure photosensitive resin into shape (class 3B)).
XFAB can be used to create 3D printed models from 3D drawings constructed with any 3D CAD software. Data is imported and processed via the "Fictor" software installed on a computer, connected to the printer via USB. The system then forwards the data to the printer, which produces 3D models by layer-by-layer curing of the resin.
The equipment must only be used for its intended purpose.
Processing Materials (Resin Type and Storage)
For detailed information on resins, please refer to the XFAB material foil.
Warning: Do not use resins other than those specified by the manufacturer.
Store resin in a sealed container, protected from light, away from light and heat sources, at temperatures between 10°C and 30°C. Use the resin within one year of the manufacturing date shown on the label. Shake the resin before use.
Warning: Before use, wear safety gloves and eye protection to avoid contact with skin and eyes.
VIII. Connecting the Printer
1. Connect the power cable (24V DC) to the printer.
2. Connect the printer to the main power supply.
3. Connect the printer to the computer using the USB cable (included).
4. Install the required software before turning on the printer.
IX. Preparation for Printing
① 3D Printer Startup
1. Turn on the printer, launch Fictor, and press the door open button ("Open").
2. Lift the printer cover (J).
3. Pull the resin cartridge latch (M2), which secures the resin cartridge top cover (M1), towards the user.
4. Place the resin tray into the printer (N), ensuring the groove aligns with the housing of the resin container (M3).
5. Shake the resin and remove the green cap from the top of the resin (R) (do not remove the protective film).
6. Press the nozzle (S) into place until fully inserted, then rotate the nozzle as shown in the diagram.
7. Insert the resin into the resin container (M3) according to the instructions on the label (items 6 and 7 to be checked after the instructions printed on the resin label).
8. Press down the resin cartridge top cover (M1) to close it. Check the resin cartridge latch (M2) to confirm the cover is locked.
② Platform Positioning (Removal Phase)
1. Check if the platform is clean and remove any dry resin residue using the specially provided comb and a lint-free cloth dampened with alcohol (ethanol).
2. Insert the platform knob (K1) into the corresponding hole (T) to place U in a horizontal position, then press until fully inserted.
3. Pull the locking lever (L) towards the user to move and rotate the platform to a horizontal position (K).
Note: Do not lock the platform at this stage.
4. Lower the printer cover (J).
X. Product Output
① Starting the Printer
1. Turn on the printer by clicking the ON/OFF button.
2. Launch the Fictor program.
3. On the Fictor main screen, click "Open" to open the printer's protective door; prepare the printer for processing.
4. Close the door.
5. Click "File" to select the 3D "file.fictor" to be printed (created using Nauta).
6. Click "Material" to select the printing material. Choose the resin type from the main menu (see processing materials).
7. Click "Home" to initialize the printer.
8. Click "Start" to start the printer.
9. The printer empties the resin tank, allowing resin to enter the resin tray.
10. Wait for the platform to be in position before locking.
11. The computer screen displays a platform lock request pop-up (V) window.
12. Open the door and lock the platform.
13. Close the door and click "OK".
② Locking the Platform
1. Lift the printer cover (J).
2. To lock the platform, follow these steps for the fixing rod (P):
a. Rotate the fixing rod forward, relative to the user.
b. Pull the rod outward.
c. Rotate the fixing rod towards the user.
d. Push the fixing rod inward.
e. Repeat the above steps until the platform is fully locked.
3. Close the printer cover (J).
③ Starting the Printing Process
Warning: During the printing process, the network connection must be maintained.
1. Press "OK" to start printing.
2. The screen displays the status of the model being printed (E). Use the following controls to customize the display of the modeling platform:
a. Start: Start/stop 3D printing process display.
b. Platform: Display platform.
c. Outline: Print image showing only the outline.
d. Reset: Reset rotation and shift.
The print completion status (D) and printer status (C) will also be displayed.
3. If necessary, you can pause the printer by clicking "Pause" or stop the printer by clicking "Stop."
4. After printing is complete, the finished product can be removed.
④Finished Product Separation (including alcohol washing stage)
1. Before separating the finished product, wear safety gloves and eye protection to avoid resin contact with skin and eyes.
2. Click "Open" and lift the printer cover (J).
3. Release the platform using the fixing rod (P) as follows:
a. Pull the rod outward.
b. Rotate the fixing rod forward, relative to the user.
c. Push the fixing rod inward.
d. Rotate the fixing rod towards the user.
e. Repeat the above steps until the platform is completely released.
4. Hold the platform handle and rotate 90° to move it to a vertical position.
5. Wait 5 to 10 minutes for excess resin to drip into the resin tray.
6. Hold the platform handle, pull the platform towards the printer, and then pull it towards the user.
7. Close the printer cover (J).
8. Keep the printed model in an upright position to prevent resin from dripping.
9. Place the platform into the cleaning tank.
10. Spray ethanol (alcohol) on the printed model to remove any excess resin.
11. To remove the model, slide the comb underneath the platform.
12. Place the model in a cleaning container.
13. Pour ethanol (alcohol) into the container and seal it.
14. Shake the container to thoroughly clean the model with alcohol.
15. Open the container, remove the model, and place it on a clean and stable surface.
16. Dry with compressed air, or wait for it to air dry naturally before use.
17. Clean the printer and the components used.
⑤Stopping the Printer
Press the ON/OFF button for 3 seconds to turn off the printer.
XI. Cleaning
Before cleaning, the printer must be disconnected from the power supply. Please wear safety gloves and eye protection to avoid resin contact with skin and eyes.
① General Printer Cleaning
Use ethanol (alcohol) and a lint-free cloth to remove any resin drips and clean the printer immediately.
Warning: Do not use ethanol (alcohol) to clean the protective cover.
Warning: Do not use water spray to clean the machine.
② Platform Cleaning (Solid and Liquid Resin)
After each use, clean the platform with ethanol (alcohol) and a lint-free cloth, ensuring all traces of cured resin are removed so that the quality of future printed models is not affected.
③ Resin Tray Cleaning
Unused resin may remain in the printer tray. Ensure the cover is closed. Alternatively, place it in a sealed container in a dark place, away from light or heat sources.
If necessary, empty the tray and clean the inside with ethanol (alcohol). For the outside, please use an alcohol-free product and a lint-free cloth to clean.